what is the pincode when pairing a JBL Charge 2+?
4. According to the quick start guide the code is 0000, so you must have other problems with your connection. Edit - that link appears to be for a Charge, this link for the Charge 2 does not show any code at all. Edit 2 - neither does this manual for the Charge 2+. Thanks, OM. I am going to look into the Charge 2+ manual anyway.
Device Bluetooth 9460/9560 don't connect JBL TUNE500BT …
2021年4月19日 · I've been trying to make my JBL TUNE500BT Headset work on Ubuntu 20.04, installed on Dell Vostro 5490, for two weeks, without success. When connecting the Headset, the service even finds the device, but at the time of connecting, there is a failure. I already updated the driver "by hand"; I have reinstalled blueman and all dependencies;
I can't turn on Bluetooth in Ubuntu 22.04 LTS - Ask Ubuntu
2022年4月22日 · Extract it and go to the folder as shown below: Copy the folder ar3k to /lib/firmware. You can also use the following command: sudo cp -R ar3k /lib/firmware. Note: Make sure you open the terminal within the extracted folder. Restart your PC and you should be able to use Bluetooth again.
Bluetooth headset with poor sound quality on Ubuntu
2015年9月22日 · For this goto open Software-Settings with software-properties-gtk and enable source. Then install the build-dependencies with sudo apt-get build-dep pulseaudio. Restart. Then, when you open your Sound-Settings you are able to choose the HFP-Profile, which enables much better sound-quality for VOIP.
How can I change the nvidia GPU fan speed? - Ask Ubuntu
2011年5月13日 · To control Nvidia GPU fan speed via Terminal on Linux Mint 20 with a 1070 Ti: sudo nvidia-xconfig --cool-bits=4. to tell nvidia-xconfig to allow the fan to be controlled in the command line. You may need to reboot here. nvidia-smi.
No sound from bluetooth headset, but it's detected - Ask Ubuntu
2013年1月10日 · Install blueman. blueman-manager &. Start blueman, and enable bluetooth as tip, if not yet. Start your headset device, make sure it's not connected to other device yet. In blueman: Search device. Right click headset -> trust, if not yet. Right click headset -> pair, if not yet. Right click headset -> audio sink.
Newest Questions - Ask Ubuntu
1answer. 20views. Mount problems with secondary encrypted btrfs disks after upgrade (Kubuntu 24.10) After upgrading to Kubuntu 24.10 yesterday, mounting my encrypted btrfs disks during boot no longer works. The system/primary boot disk, which is also encrypted, is not affected.
How to set wifi driver settings to prefer 5 GHz channel above 2.4 …
2012年9月3日 · This will set the network to use 5 GHz only. If you want to use 2.4 GHz, use band=bg instead. When you are done editing, press CTRL + o and then press ENTER to save the file and then press CTRL + x to exit nano. Finally, restart network-manager to apply the changes: sudo systemctl restart network-manager.
power management - How to control fan speed? - Ask Ubuntu
2016年5月27日 · Configure fancontrol. In terminal type sudo pwmconfig. This script will stop each fan for 5 seconds to find out which fans can be controlled by which PWM handle. After script loops through all fans, you can configure which fan corresponds to which temperature. You will have to specify what sensors to use.
How do I install iTunes on Ubuntu? - Ask Ubuntu
2014年2月3日 · sudo apt-get install curl p7zip-full p7zip-rar. Now run it. sudo playonlinux. iTunes on Ubuntu. Download iTunes. Navigate to the already open PlayOnLinux window and click on Install a non-listed program as shown below. Browse to the iTunes setup file. Click on Next and follow the installation instructions. source.